Eager to grow – Marsh Marigold and Wood Poppy

by Sandy Garland

2-week-old wood poppy seedlings

2-week-old wood poppy seedlings

Some seeds just can’t wait to get growing.

Every year we collect seeds from our wildflowers at the FWG and some from the wild to grow for our annual plant sale (first Saturday in June). In the fall, we carefully mix them with damp vermiculite – or leave them in paper envelops if that’s what they require – and store them in the refrigerator to simulate winter. This allows us to get them out and germinating early so that they will be a good size by June.

For the last few years, I’ve found a few species sprouting in January while they are still in the refrigerator – wood poppy, marsh marigold, and Virginia bluebells. I have found wood poppy and marsh marigold difficult to grow; we tried both many times in the past with no success.

Finally, I tried initiating the cold treatment as soon as the seeds are mature – late spring. This produced excellent results, but there is still a problem. Although the seeds happily sprout in January, and grow well for a couple of months, many plants then slowly wilt and die.

Last year, my entire “crop” of Virginia bluebells disappeared in April and May. I speculated that having been roused from dormancy in January, they had already gone through a normal life cycle by April and died back as normal plants in the wild would have done. They didn’t bloom, but many wildflowers don’t flower the first year. I kept all the tiny tubers and I’m hoping they’ll show signs of life at the normal time this year.

I’m afraid there’s no happy ending to this story – yet. At the moment, I have 18 marsh marigold and about a dozen wood poppy seedlings that I will try to coax to maturity. And 4 flats of Virginia bluebell tubers that I hope will grow when their snow cover melts.

If anyone has experience growing these or similar wild species, I would love to hear from you.

See also: Growing native plants from seed: cold stratification
Growing common milkweed from seed: easy steps for beginners

Growing native plants from seed : cold stratification

A damp vermiculite-filled baggie awaiting seed.

In late October, although we’re still waiting for some seeds to mature before we can collect them, others are ready for their winter treatment.

So what is cold stratification? Essentially, it’s a temperature and moisture treatment used to break a seed’s dormancy and encourage germination. In nature, seeds fall to the ground, where they are covered by leaves and other pieces of decomposing vegetation. Snow falls, covering the seeds with a blanket and insulating them from extreme temperatures and drying wind. In spring, as the snow melts and the sun gradually warms the soil, the seeds germinate and begin to grow!

The need for this cold period to break dormancy is an adaptation to winter. Imagine if seeds germinated almost as soon as they fell off a plant; most plants would die as soon as the cold hit, as they would be too small to have sufficient root mass to survive.

Because we start plants for our annual June sale early, we need to be able to control when they go to sleep and wake up. This is surprisingly easy. All you need are small sealable baggies (we use the snack size), a bowl, a spoon, vermiculite, tepid water, and labels.

Note: The following instructions are for cold, moist stratification, needed by most seeds in our area. However, please check a suitable reference, such as the New England Wildflower Society’s  Growing and Propagating Wildflowers, to find out which species need moisture, which should be stored dry, and which need no treatment at all.

1. Prepare damp vermiculite
Pour some vermiculite into the bowl and add just enough water to wet it. Wait a few minutes as the water is absorbed, then add more water until the vermiculite is damp to the touch. There should not be any standing water in the bottom of your bowl, but the flakes of vermiculite should look and feel moist. Stir with the spoon to distribute the moisture. Vermiculite is a mineral that holds a lot of water, making it ideal to keep the seed environment moist over a long period.

Removing fluff from a milkweed species. Fluff gets everywhere!

Removing fluff from a milkweed species. Fluff gets everywhere!

2. Prepare seeds
Remove seed cases and as much debris from the seeds as possible to reduce the likelihood of rot. Some casings contain germination inhibitors, so making sure the seeds are “clean” can be important.

We remove the silk parachutes from milkweed and open all seed pods to release the actual seeds. But we don’t try to pull the fluff off clematis, prairie smoke, goldenrod, or aster seeds.

3. Prepare baggies
Put about three spoonfuls of damp vermiculite into a baggie. Add just enough seeds that every one has lots of contact with the vermiculite. As a rough guide, the volume of vermiculite should be about twice that of the seeds.

We like to shake and then pat down the baggie to maximize contact. Gently push out most of the air, and seal the baggie. You now have a fairly flat, cool to the touch, and moist seed baggie ready for placing in the refrigerator. Don’t forget to label it! We use business labels, because they can be peeled off in spring and attached to our germination containers.

4. Store in a cold place
We have a mini-fridge dedicated to seeds, so moisture levels and temperature are constant (unless someone accidentally knocks the dial). However, your home refrigerator should be just fine, if you place your seeds near the back and away from where moisture tends to collect.

Labeling seed properly is essential. Here you can see our box full of seed baggies!

Now you can forget about your horde until late January or early February!

In early February, remove the baggies from the refrigerator and dump the entire contents into clear sandwich containers. Anything with a clear lid and no holes will work. Label each container so you know what is inside. Again, consult a good reference book to find out which species need light to germinate and which germinate in the dark.

Some seeds germinate almost immediately; others require considerable patience. Keep an eye on moisture levels – keep the vermiculite moist, but not wet. Once the sprouts have at least a couple of mini leaves (they look just like the edible sprouts you buy in stores at this stage) you can begin the next phase which is planting them into a seed starting soil mixture. But that is the subject for another post!